In order to meet the needs of customers and the market, our company continues to develop timely new Electrophoresis Painting, ED coating component system, cathodic electrophoretic coating frame system. As an industry-leading manufacturer of electrophoretic coating surface preparation system, our success stems from our expertise and experience. We use outstanding materials and production techniques to create innovative products that change people's lives. Since the creation of our company, we keep introducing new products so that has a good reputation worldwide. We adhere to a high starting point, high standards, high speed, and continue to pioneer and innovate, advancing with the times. Over the years, the company has won the favor and trust of customers at home and abroad with its efficient production capacity, strict quality management system, high-quality and innovative products, and warm and thoughtful service. We are committed to increasing market penetration in many countries, especially in emerging economies. Our team is dedicated to providing exceptional customer support and service.
-
![Cathodic Electrodeposition Coating]()
Cathodic Electrodeposition CoatingA big benefit of the electrocoat process is thickness control. With our product, you can adjust the voltage and time. You can get from a 5-micron ultra-thin protective layer to a 35-micron heavy-duty -
![Electrophoretic Painting]()
Electrophoretic PaintingGreat adhesion does more than just hold the paint on. It also improves rust protection. A coating that sticks well blocks water and oxygen from moving sideways under the film. Even if the film is -
![Electrodeposited Coatings]()
Electrodeposited CoatingsWith traditional spray, the thickness depends on the worker's hand. It can be uneven. But this process is controlled by electricity. As the film gets thicker, it acts as a resistor. The deposition -
![Cathodic Electrodeposition Paint]()
Cathodic Electrodeposition PaintThis product is not just high-performing. It also helps with your energy cost. The baking window is wide. It cures fully between 160°C and 180°C. This is 10-20°C lower than traditional products. Do -
![Electrophoresis Metal Coating]()
Electrophoresis Metal CoatingA good coating must look good. It must also survive the next steps. Your workers will bend and punch the parts. Our coating has a hardness of 2H to 3H. It can handle small scratches during assembly. -
![Electrophoretic Paint]()
Electrophoretic PaintIn the area of rust protection, this two-component system is also very strong. We can use more anti-rust pigment. Or we can use a special resin that grabs onto the metal. In the ASTM B117 salt spray -
![Water Based Paint Environmentally Friendly]()
Water Based Paint Environmentally FriendlyThis product is special because we stopped using any organic solvents. The main material is a water-based epoxy resin. Some of it even comes from plants. The hardener is also one that mixes with -
![Cationic Electrodeposition Coating]()
Cationic Electrodeposition CoatingWhat do coatings fear most? Water. Water can get between the film and the metal. Then the film can bubble and peel. Our cationic product is very strong in wet conditions. We did a humidity test at -
![Electrophoretic Lacquering]()
Electrophoretic LacqueringWe designed this formula for general industry. We use a medium-weight epoxy resin. This gives a good balance of hardness and flexibility. It works well for many types of hardware. The pigments are -
![Electro Deposition Painting]()
Electro Deposition PaintingThe formula for this product was designed with the whole process in mind. It works with the pre-treatment (cleaning and phosphating), the electrodeposition, the rinses, and the baking. Each step must -
![Electrophoretic Coating]()
Electrophoretic CoatingSome metals cannot take high heat. This includes some aluminum, magnesium, and composites. Our two-component system has a special low-temperature hardener. It can cure fully at 130-150°C for 20-30 -
![Electrophoresis Painting]()
Electrophoresis PaintingThis product uses a standard epoxy-isocyanate system. It has a medium solid content of 12-18%. This gives good coating efficiency and bath stability. The pigments are good quality titanium dioxide
Bernadette Figueredo
The customer service staff is very patient and has a positive and progressive attitude to our interest, so that we can have a comprehensive understanding of the product and finally we reached an
Jacqueline Ferguson
The customer service staff's answer is very meticulous, the most important is that the product quality is very good, and packaged carefully, shipped quickly!
Harry Millender
Product variety is complete, good quality and inexpensive, the delivery is fast and transport is security, very good, we are happy to cooperate with a reputable company!
Kayla Gibbs
This is the first business after our company establish, products and services are very satisfying, we have a good start, we hope to cooperate continuous in the future!
Herbert Cox
Production management mechanism is completed, quality is guaranteed, high credibility and service let the cooperation is easy, perfect!
Jack Finn
Product quality is good, quality assurance system is complete, every link can inquire and solve the problem timely!
We are committed to becoming a benchmark in the electrophoretic coating drying line, cathodic electrophoretic coating filtration system industry. Relying on the continuous improvement of product quality and high-quality service concept, we have successively cooperated with many domestic and foreign merchants. We're well-known as one of the leading electrophoretic coating surface preparation system manufacturers and suppliers in China, featured by quality products and low price. Please rest assured to buy discount electrophoretic coating surface preparation system from our factory. We also accept customized orders.